SIP ALG uitschakelen

Adtran

Add the following:

no ip firewall alg sip

 

Arris Gateways

  1. Go to Advanced > Options.
  2. Disable (uncheck) SIP.
  3. Click Apply.

Arris Gateway IP Address: 192.168.0.1

  • Username: admin
  • Password: motorola

 

ASA

  1. Go to policy-map global_policy > class inspection_default.
  2. Enter:
no inspect sip

 

ASUS

SIP ALG is located in (via the web interface):

  1. Go to Advanced Settings / WAN on left side.
  2. From the tabs across the top, choose NAT Pass through.
  3. Change SIP pass through to “Disable.” Hit apply.

For phones to pick up the change immediately, reboot each of them, otherwise they will pick up the new NAT table with changes during their next registration.

If your router does not have an option to disable SIP Passthrough then read on…

To disable the SIP ALG manually, you enable telnet to the device via the WWW interface.

Telnet to the device (from a command line enter “telent 192.168.1.1” or the appropriate IP address for the device.)

Issue the following commands:

nvram get nf_sip 
(It should return a "1")
nvram set nf_sip=0 
nvram commit
Reboot

Then reboot the router for the changes to take effect.

 

Cisco

On Cisco devices, SIP-ALG is referred to as SIP Fixup and is enabled by default on both routers and Pix devices. Because this is a default setting, no indication of it being “on” or “off” is visible in the configuration.

To disable SIP Fixup, issue the following commands:

General Routers

no ip nat service sip tcp port 5060
no ip nat service sip udp port 5060

Enterprise-Class Routers

no ip nat service sip tcp port 5060
no ip nat service sip udp port 5060

Pix Devices

no fixup protocol sip 5060
no fixup protocol sip udp 5060

Models: 800 Series

To disable the NAT services for SIP in IOS, just run these commands:

no ip nat service sip tcp port 5060
no ip nat service sip udp port 5060

 

D-Link

  1. From the admin interface page of the router, navigate to Advanced settings.
  2. Under Application Level Gateway (ALG) Configuration, uncheck the SIP option.

 

Draytek

Voor de modellen: Vigor2750, Vigor2130

SIP ALG staat standaard aan. Mocht je dit willen uitzetten:

  • Zorg ervoor dat de computer met de router verbonden is.
  • Open een commandline;
    • Windows: Start -> Uitvoeren -> type cmd-> enter
    • OS X: CMD+spatie -> type terminal-> enter
  • Type in deze commandline telnet IP-van-de-routeren druk op enter
  • Type de gebruikersnaam in van de modem en druk op enter
  • Voer het wachtwoord van de modem in en druk nogmaals op enter
  • Voer het volgende in en druk op enter: kmodule_ctl nf_conntrack_sip disable
  • Voer het volgende in en druk op enter: kmodule_ctl nf_nat_sip disable
  • Als het modem herstart is kunt u testen of VoIP werkt.

Alle andere modellen:

  • Zorg ervoor dat de computer met de router verbonden is.
  • Open een commandline;
    • Windows: Start -> Uitvoeren -> type cmd-> enter
    • OS X: CMD+spatie -> type terminal-> enter
  • Type in deze commandline telnet IP-van-de-routeren druk op enter
  • Type de gebruikersnaam in van de modem en druk op enter
  • Voer het wachtwoord van de modem in en druk nogmaals op enter
  • Voer het volgende in en druk op enter: sys sip_alg 0
  • Als het modem herstart is kunt u testen of VoIP werkt.


Time-To-Live UDP:

Er zijn enkele modellen waar de TTL voor UDP aangepast dient te worden indien gebruik worden gemaakt van het RoutIT platform:

– Express Office / Hosted Basis: 40 seconden
– HIP / Hosted Extra: 100 seconden

By telnet command “portmaptime -l”, we can check the current value for each application.

To change the NAT timeout value, enter command

portmaptime -[protocol] [time]

Where [protocol] is a character represents the application (please use command “portmaptime ?” to check the options available), and [time] is a number of seconds. For example, if you’d like to set the timeout value of UDP session to 5 minutes (300 seconds), this can be done by the command

portmaptime -u 300

After that, you may use the command “portmaptime -l” to check if the current value has changed.

 

Fortinet

Models: All models come with SIP Helper enabled by default

To disable SIP helper:

~# telnet firewall
config system settings
set sip-helper disable
set sip-nat-trace disable
end
config system session-helper
show <---- use this to find out which entry is configured for typically 12 or 13
delete 12
end

The preferred solution is to configure the SIP ALG. Policies that use the SIP ALG will not use SIP helper. Full documentation at http://docs.fortinet.com then pick FortiOS for the version on your device, then VoIP solutions: SIP.

 

Juniper / Netscreen

Models: SSG Series

To disable SIP ALG:
In the Web interface: Security -> ALG

 

Linksys

General Linksys Guidelines

  1. From the ADMIN page of the router, navigate to [Administration] > [Advanced].
  2. Look for and disable a SIP ALG option.

Linksys BEFSR41

  1. From the ADMIN page of the router, navigate to [APPLICATIONS & GAMING] > [PORT TRIGGERING].
  2. Enter [TCP] as the application.
  3. Enter [5060] into the Start Port and End Port for both the Triggering Range and Forwarded Range.
  4. Check Enable.
  5. Save Settings.
  6. Reboot IP phone.

Models: WRV200, WRT610N
NAT type: Symmetrical
Issues:

  • The ALG replaces the private address in “Call-ID” header (not needed at all). Some phones (as Linksys with latest firmware) encode the “Call-ID” value in the “Refer-To” header (by escaping the dots) so the private IP appearing there is not replaced with the public IP. This causes that the call transfer fails since the proxy/PBX/endpoint will not recognize the dialog info.

To disable SIP ALG:

ToDo no ALG related options found via web and telnet. No idea of how to disable it.
To disable SIP ALG on WRT610N: Web Interface: Administration, Management, under side heading ‘Advanced Features’ SIP ALG, can be disabled.

 

Motorola

Models: SBG6580 (SurfBoard Extreme Wireless Cable Modem Gateway)

  • No Registeration possible behind NAT as the device changes Call-ID and causes the responses to be discarded by SIP clients/ATAs
  • No Solution at this time (SIP ALG, called SIP Pass Through, can not be disabled) .
  • Must disable NAT and put the device in bridge mode. (See this guide)

 

Netgear

Models: WGR614v9 Wireless-G Router, DGN2000 Wireless-N ADSL2+ Modem Router
Firmware V1.0.18_8.0.9NA
To disable SIP ALG:

  1. From Wan Setup Menu,
  2. NAT Filtering,
  3. uncheck the box next to “Disable SIP ALG”

When setting the Global Default UDP timeout value on a SonicWall firewall, you must still fix the pre-existing rules’ individual UDP timeout values. New rules will inherit the Global Default. Increase the UDP timeout to the suggested 300 seconds both globally on the firewall and the specific out-bound firewall rule (or the default rule, as the case may be).

RoutIT platform:
– Express Office / Hosted Basis: 40 seconden
– HIP / Hosted Extra: 100 seconden

 

Peplink Multi-WAN routers

Models: All multi-WAN models
To disable SIP ALG, go to http://<router.LAN.IP>/cgi-bin/MANGA/support.cgi
Click the “Disable” button under “SIP ALG Support”
Issues:

  • I’m not aware of any SIP ALG issues, but if you just want to turn it off, here you go.

 

SMC

Models: ToDo
NAT type: No symmetrical
Issues:

  • The ALG doesn’t replace the private address in “Call-ID” header (that is correct) but it does replace the “call-id” value in “Refer-To” header so SIP transfer is broken.

To disable SIP ALG:

ToDo no ALG related options found via web and telnet. No idea of how to dissable it.

 

SonicWall

  1. Uncheck the box for Use SIP Header Transformation.
  2. Disable consistent NAT.

When setting the Global Default UDP timeout value on a SonicWall firewall, you must still fix the pre-existing rules’ individual UDP timeout values. New rules will inherit the Global Default. Increase the UDP timeout to the suggested 300 seconds both globally on the firewall and the specific out-bound firewall rule (or the default rule, as the case may be).

RoutIT platform:
– Express Office / Hosted Basis: 40 seconden
– HIP / Hosted Extra: 100 seconden

 

SpeedTouch

Models: ST530 v6 (firmware >= 5.4.0.13) comes with SIP ALG enabled by default.
NAT type: symmetrical
Issues:

  • No incoming calls.
  • It replaces the private IP appearing in SIP headers with the public IP using a dumb text replacement. If for example the private IP appears in the “Call-ID” it replaces it too (that it’s completely unnecessary).

To disable SIP ALG:

~# telnet router
-> connection unbind application=SIP port=5060
-> saveall

 

UBEE

  1. Go to Advanced > Options.
  2. Disable (uncheck) SIP.
  3. Disable (uncheck) RTSP.
  4. Click Apply.

 

Ubiquinti

Model: Edgerouter

  1. Open de Config Tree.
  2. Klap het menu open zoals hieronder aangegeven.
  3. Klik op  + achter disable onder sip.
  4. Klik onder in beeld op Preview om de instellingen op te slaan.

 

Zyxel

  1. Go to Settings > Configuration > Network > ALG.
  2. Disable SIP ALG.

Note: If you have mixed models of phones like Polycom/Aastra/Cisco/Panasonic, then you may experience difficulty in using ZyXEL ZyWALL routers. However, if you have only Polycom phones, please review this article to learn how to configure ZyXEL ZyWALL routers for use with Polycom phones.

Models: 660 family comes with SIP ALG enabed by default.
NAT type: symmetrical
Issues:

  • No incoming calls.
  • SIP protocol broken making 50% of outgoing calls impossible because the wrong values are inserted into SIP headers.

To disable SIP ALG:

~# telnet router
Menu option "24. System Maintenance".
Menu option "8. Command Interpreter Mode".
ip nat service sip active 0